Effect of Heat Exposure Time on Tensile Properties in Cold Rolled Steel
الشريط الجانبي للمقالة
محتوى المقالة الرئيسي
الملخص
This paper presents the effect of heat exposure time on tensile strength of cold rolled specimens. Welding and process annealing are applied to the specimens to investigate their implications. The two processes involve heat and time but in differential amounts. In welding the temperature raises to levels far beyond the melting point of the specimens and cools quickly. The case is different in process anneal the specimen temperature increases slowly to the subcritical level and cools slowly after a specific soaking time. Welded and process annealed in the form of tensile specimens are tested in the tensile machine until fracture. The test results showed that welding and process annealing caused a decrease in yield strength by one third and almost two thirds respectively compared with the as rolled. The fracture of the welded specimen was localized at the heat affected zone near the weld line but was random in all other specimens. Percentage elongation was lowest in the welded specimen compared with other patches of specimens.
تفاصيل المقالة
هذا العمل مرخص بموجب Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
المراجع
R. Abbaschian, L. Abbaschian, and R. E. Reed-Hill, Physical Metallurgy Principles, Fourth Edition, Cengage learning, Inc. USA, 2009.
W. F. Hosford, Physical metallurgy, Taylor and Francis Group, 2005.
D. R. Askeland, P. P. Fulay, W. J.Wright, The science and engineering of materials, Sixth Edition, Cengage learning, Inc. USA, 2010.
W. D. Callister, Materials science and engineering an introduction, seventh edition, John Wiley & Sons, Inc.,2007.
R. E. Smallman, R. J. Bishop, Modern Physical Metallurgy and Materials Engineering, Sixth Edition, Reed Educational and Professional Publishing Ltd 1995, 1999.
G. E. Dieter, Mechanical Metallurgy, SI Metric edition, McGraw-Hill book co.,1988.
T. G. Digges, S. J. Rosenberg, and G. W. Geil, Heat treatment and properties of iron and steel, U.S. Government Printing Office, Washington, D.C., 1966. DOI: https://doi.org/10.6028/NBS.MONO.88
G. E. Totten, Steel heat treatment metallurgy and technologies, second edition, Taylor and Francis Group, 2006. DOI: https://doi.org/10.1201/NOF0849384523
Sindo Kou, Welding Metallurgy, Second Edition, A John Wiley & Sons Inc., 2003.
R. Blondeau, Metallurgy and Mechanics of Welding, John Wiley & Sons, Inc. 2008. DOI: https://doi.org/10.1002/9780470611272
M. I. Khan, Welding science and technology, New age international publishers, 2007.
H. Mehrer, Diffusion in Solids, Springer-Verlag Berlin Heidelberg, 2007. DOI: https://doi.org/10.1007/978-3-540-71488-0
Z. Larouk, and H. Bouhalais, ''Recrystallization behavior of a low carbon steel wire,'' Physics Procedia, Vol. 2, pp. 1223-1229, 2009. DOI: https://doi.org/10.1016/j.phpro.2009.11.085
I. Schindler, M. Janosec, E. Mistecky, M. Ruzicka, L. Cizek, L.A. Dobrzanski, S. Rusz and P. Suchanek, ''Effect of cold rolling and annealing on mechanical properties of HSLA steel,'' Archives of Materials Sciences and Engineering, International Scientific journal, Vol. 36, No. 1, pp. 41-47, 2009.
W.S.Muda, N. S.Nasir, S. Mamat, and S. Jamian, ''Effect of welding heat input on microstructure and mechanical properties at coarse grain heat affected zone of ABS grade A steel, ''ARPN Journal of Engineering and Applied Sciences, Vol. 10, No. 20, pp. 9487-9495, 2015.
S.I. Talabi, O.B. Owolabi, J.A. Adebisi, and T. Yahaya, ''Effect of welding variables on mechanical properties of low carbon steel welded joint,'' Advances in Production Engineering & Management, Vol.9, No. 4, pp. 181-186, 2014. DOI: https://doi.org/10.14743/apem2014.4.186
P. A. O. Adegbuyi and A. Atiri, ''The Effect of Annealing on the Microstructure and Mechanical Properties of a Rolled Steel Product, ''The Pacific Journal of Science and Technology, Vol. 10, No. 2, pp. 149-162, 2009.
N. A. Raji and O. O. Oluwole, ''Effect of Soaking Time on the Mechanical Properties of Annealed Cold-Drawn Low Carbon Steel, ''Materials Sciences and Applications, Vol. 3, pp. 513-518, 2012. DOI: https://doi.org/10.4236/msa.2012.38072